Exactly How to Install a Bath Tub Yourself: Removing as well as Replacing.
Exactly How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
We've noticed this great article pertaining to A Step-by-Step Guide to Installing a Bathtub below on the web and accepted it made good sense to relate it with you over here.
Mounting a bathtub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably hard job. If the old tub is easily easily accessible, the task can relocate immediately; if you need to open a wall surface to remove the old bathtub and place the new tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will need an assistant to leave the old bathtub and embeded in the new one. Make certain you have certified on your own for the work as well as fit trying it. Rather than hiring a service provider to take over a halfway-completed job, it is better to consider utilizing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This short article will aid you install a new bath tub in your washroom if you have actually already gotten a brand-new bathtub and also do not require to transform the setup of your previous water supply pipes.
Your tools and material checklist need to consist of the following:
Planning for the Installment
To start with, the sustaining frame supplied with the bathroom must be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to stop strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its final setting.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, after that the first thing you must do is disconnect the water system. After doing so, switch on the faucets to drain any water remaining in the system. The procedure of eliminating the existing taps can be rather bothersome due to the limited accessibility that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the remaining water that will certainly come from the pipelines. Once the supply pipes have actually been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Before carrying on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using both wooden boards under its feet, place the tub in the required position. The wooden boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the tub up until the spirit level reviews degree.
To install faucets, fit all-time low of the furthest flexible faucet adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water supply and inspect all joints as well as new pipework for leaks and also tighten them if necessary. Fill the bathtub as well as also inspect the overflow outlet and the normal outlet for leakages.
Ultimately, deal with the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub needs to wait up until the bathtub has been utilized a minimum of once as this will settle it into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin ensuring that the washers are in area in between the faucet and also the sink. Secure the faucet in position with the maker provided backnut. Once the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former type must be linked to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, causing the water to penetrate the wall surface between the bath and the tiling, causing issues with moisture and feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and also installations. They are sold in tubes as well as cartridges, and also can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water before securing, to permit the movement experienced when the tub remains in usage. The sealer can split relatively early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub Yourself? Create a review down the page. We'd be interested to see your insights about this content. We are looking forward that you visit us again before long. Do you know about somebody who is interested by How to Install a Bathtub Yourself? Why not promote it. Many thanks for your time invested reading it.
Additional Resources Report this page